MultiDyne

• 16 Channel SDI embedded audio monitoring system
• 16 bar graph VU/PPM meter on display
• ITU1770-3/1771 measurements 
• SDI signal status on the display
• Twelve illuminated pushbuttons
• 1/4" jack
• 3G/HD/SD-SDI signal can be connected to the
• 2x 3-Pin terminal block connectors
• GPI connector
• Ethernet port 

• 16 bar graph VU/PPM and ITU1770-3/1771 measurements on display
• SDI signal status
• LKFS meter
• Twelve illuminated pushbuttons
• SDI 1, SDI 2, or AES/ANALOG
• 1/4" jack 
• 3G/HD/SD-SDI signals can be connected to the BNC connector
• 75 Ohm Unbalanced AES/EBU input is on a BNC connector
• 2 channel analog audio input is on two 3 Pin terminal blocks
• 2x 3-Pin terminal block connectors
• GPI connector

• 20-slot openGear Frame
• 2 Rack Units with Fans and Metal Plates on Rear I/O
• Includes one PS-OGX power supply and MFC-8320-S Simple Network Controller Card

* Does not support Copy/Upload Parameters. Supports Save

* no I/O modules, No SNMP

* Requires extra PS-OGX for redundant power

• Redundant/Replacement Power Supply
• For Cobalt PS-oGx OpenGear Frame
• 600W Continuous Maximum Operation
• 100-240V, 60/50 Hz IEC Connector
• Hot-Swappable
• Accessible from Front of Frame

The MDoG-6001-DA8-AESB is a 110 Ohm AES/EBU digital audio distribution amplifier designed for broadcast use. It provides 8 copies of the incoming balanced AES3 signal when used with the R2-6001-DA8-AESB full rear module or 4 copies of the incoming signal when used with the R2-6001-DA8-AESB split rear module.

The MDoG-6021-ADC-2AESU quad analog audio to 75 Ohm AES/EBU converter is a broadcast quality, modular solution, which converts 4 analog audio channels to 2, 24-bit, unbalanced AES-3id signals.

• Configured as 3 Tx & 3 Rx
• Over SIX fibers
• For: SD/HD/3G-SDI, DVB ASI, SMPTE 310M
• ST fiber connectors (Requires 2 units to make one operational set)
• 6 to 18 SDI signals on 6 or ONE fiber
• Fiber transport from 125Mbps to 3Gbps
• Supports SMPTE 424M, 292M, 259M, 310M, 344M, 305M & DVB-ASI
• Equalizes 120m of Gepco VSD2001 or Belden 1694A cable at 3 Gb/sec
• Optional OLED display for system status and reclocking on/of
• Easy access to installed fiber infrastructures

• 12 fibers
• For: SD/HD/3G-SDI, DVB ASI, SMPTE 310M (1 RU enclosure w/ rack ears for rack mounting included)
• Fiber transport from 125Mbps to 3Gbps
• Supports SMPTE 424M, 292M, 259M, 310M, 344M, 305M & DVB-ASI
• Equalizes 120m of Gepco VSD2001 or Belden 1694A cable at 3 Gb/sec
• Optional OLED display for system status and reclocking on/of
• Easy access to installed fiber infrastructures

• SilverBULLET™ 3.0 Gbps Multi-rate Serial Digital Video Transmitter 1310nm
• -6dBm for: SD/HD-SDI, DVB ASI, SMPTE 310M, ST connector

• Sensitivity -20 dBm
• for: SD/HD-SDI, DVB ASI, SMPTE 310M
• ST connector

• Camera side
• Portable
• 2 singlemode fibers (ST connectors)
• Hybrid cable SMPTE-304M plug connector
• Provides power and signal transport to Sony HDC series, Panasonic, Ikegami, and Hitachi cameras  

• CCU Side
• Portable
• Hybrid cable SMPTE-304M socket connector
• 2 singlemode fibers (ST connectors)
• For Sony HDC series, Panasonic, Ikegami, and Hitachi cameras only

• 4 x 4 matrix over 1 fiber
• Supports SD-SDI, HD-SDI, 3G HD-SDI, DVB ASI, SMPTE 424M,292M/259M/310M
• EQ and Reclocker
• CWDM (R2 range wavelengths: 1351, 1411 - 1451nm)
• Single-mode
• Supports embedded audio (Requires R2-4400-CWDM-xx Rear IO Module & OGX-FR-x openGear frame for operation)  

• 4 x 4 matrix over 1 fiber
• Supports SD-SDI, HD-SDI, 3G HD-SDI, DVB ASI, SMPTE 424M,292M/259M/310M
• EQ and Reclocker
• CWDM (R3 range wavelengths: 1471 - 1531nm)
• Single-mode
• Supports embedded audio (Requires R2-4400-CWDM-xx Rear IO Module & OGX-FR-x openGear frame for operation)